Ring Lock Scaffolding Side bracket is used at the edge of a scaffolding to extend the reach or extension off of any side of the scaffolding where sunshade comes.
Ring Lock Scaffolding Lattice Beams are the horizontal members that allow for scaffolding over large spans or gaps, offers suspended, walk through and beam support in Construction. Sizes of the Lattice Beams are in 10 ft to 28 ft according to construction design and 500mm depth.
Ring Lock Scafolding Double ledgers are horizontal members ing that allow for increased load carrying capacities not possible with single tube or regular duty ledgers. They provide increased horizontal support for loads and planks.
Speed Shore Kwikstage scaffolding is the type of heavy duty kwiskstage system scaffold that used for concrete slab formwork solutions with sleeved standard, C-ledgers, trigger brace, solid adjustable screw jack base , forkhead jacks, rail post etc.
Kwikstage Scaffolding Return transom allows a 90 degree turn in the scaffold and sit over the ledger allowing boards to run at right angles in adjacent bays. It can also be used to change direction. The use of Return Transoms eliminates the " gap " between runs at right angles.
Kwikstage Ladder Access Transom is used where a ladder access or trapdoor is required inside a bay. The Ladder Access Transom is located between the two ledgers, this is placed approx 64" from the previous transom. To be used with a Safety Trap-Door, a single section verticle ladder is held in place with 4 nos Metal Ladder Clamp. We recommend that 1
Kwikstage Mesh Panel / Brick Guard is placed between the ledger and the steel plank. Designed to be suspended from a guard rail ledger enclosing the space between the ledger and the working platform for safety.
Kwikstage Scaffolding Hop Up Brackets are used to give an extra work platform for scaffolding. Normally located on the inside face of the scaffold, these are 1, 2 and 3 board sizes.
Kwikstage Scaffolding Hop Down Bracket / Step Down Bracket gives balance and stability to the bottom step when getting on or off stair access at ground level. The first step onto stair access can be difficult due to site constraints, ground levels and base outs. The use of the step down bracket gives the comfort of adjustment to balance the variabl1
Kwikstage Scaffolding Tie Bars have pins at each ends which fit in holes of 2 and 3 Hop Up Brackets to prevent the brackets spreading and the planks from becoming dislodged.
Kwikstage Internal Corner Board is used to fill in the gap ineternal corners when stage board brackets are used. It is a safe element to fill space between boards and standards to form a safe work platform and leveling. The internal corner boards sizes include one boards, 2 boards, 3 boards according to the width.
Kwikstage Scaffolding Steel Plank is a kind of plank which is designed and fabricated as per the Standard requirement of Australia/New Zealand AS 1577. It is made by 1.8mm or 1.5mm steel plate and hot dip galvanized. The planks are no hooks at both ends and to be installed onto the scaffolding transoms.
Kwikstage Scaffolding Toe Board / Kick Board is the component that prevents the building materials or tools falling off from working platform. The toe board has bolts at the ends to hold itself sitting between two verticals post of the platform.
European Type Steel Plank is one kind of high safety dedsigned plank for Ring Lock System Scaffolding. It is designed with 320mm wide and wide hooks for tubular ledger (O Ledger). The plank is hot dip galvanized for long lasting use.
South-East Asia Type of Steel Plank is a kind of economical, light weight, good quality scaffolding plank. It is normally used for coupler-tubular scaffolding, it is in 240mm or 210mm wide, and in the length of 0.5m, 1.0m, 1.5m, 1.0m, 1.5m, 2.0m, 2.5m, 3.0m, 3.5m, 4.0m.
Steel Plywood formwork is made by steel frame and filmed plywood form, it is a kind of is a pre-engineered, factory-built, reusable in situ concrete forming system. It saves time because it is easy to set up and strip. No measuring, sawing, drilling, or nailing is required. The only tool required for setup and stripping is a hammer.
German Type Ringlock Scaffolding,also called Allround scaffolding, typical product layher scaffolding, is one of the most popular system scaffolding or modular scaffolding for construction. It is widely used in the construction industry, such as building, bridge, viaduct, petrochemical, shipyard, aircraft maintenance, etc. It supports to access wor1
Ring Lock Scaffolding Diagonal Braces, also called Bay Braces or Vertical Braces, serve to give lateral support to the scaffold. They can also be used as guard rails in stair system, or tension and compression members. It is made from O.D 48.3x2.5mm scaffold tube with cast steel brace head and wedge pins at both ends.
