All aluminum Plank is made by 6061-T6 or 6082-T6 aluminum extrusion, plank width 19" (483mm), plank length from 3' to 10'. The plank complies with OHSA & ANSI A10.8 requirements. Safety load is 75lb/ft2.
Aluminum Plywood Plank is made by 6061-T6 or 6082-T6 aluminum extrusion and fire-proof plywood panel, plank width 19" (483mm), plank length from 3' to 10'. The plank complies with OHSA & ANSI A10.8 requirements. Safety load is 75lb/ft2.
Aluminum Plywood Ladder Hatch Deck is made by 6061-T6 or 6082-T6 aluminum extrusion and fire-proof plywood panel, plank width 24" or 28", plank length from 7' to 10'. Hatch Ladder: Aluminum 6061-T6, 7-step ladder The plank complies with OHSA & ANSI A10.8 requirements. Safety load is 75lb/ft2.
2.0m Aluminum Stretcher Stairs are designed specifically for use with the traditional steel kwikstage system scaffolding. They are pre-fabricated and designed to fit in a 1.27m x 2.44m bay with a 2.0m lift. The stair ends are flat so that it can lay on the transoms. The stairs are 560mm wide with a rise of 230mm. Two stairs (lift and right stretche1
2.0m Aluminum Stretcher Stairs with Hooks are the type of stretcher stair with long u-shape hook welded at the two ends. By thehooks, the stairs can widely use for all kinds of modular scaffolding system, such as kwikstage, ring lock, cup lock scaffolding. They are pre-fabricated and designed to fit in a 1.27m x 2.44m bay with a 2.0m lift. The1
Kwikstage Stairway (Steel) is the safe & easy solution for vertical access in lightweight with non-slip treads and platform. It is fabricated and designed to fit in a 1.27x2.44m scaffolding bay with 1.5m lift height. It is a specially design to fit in 1.2m tranom for two stairs side by side installation. The stairs are hot dip galvanized.
Ring Lock Scaffolding Lattice Beams are the horizontal members that allow for scaffolding over large spans or gaps, offers suspended, walk through and beam support in Construction. Sizes of the Lattice Beams are in 10 ft to 28 ft according to construction design and 500mm depth.
Ring Lock Scafolding Double ledgers are horizontal members ing that allow for increased load carrying capacities not possible with single tube or regular duty ledgers. They provide increased horizontal support for loads and planks.
Speed Shore Kwikstage scaffolding is the type of heavy duty kwiskstage system scaffold that used for concrete slab formwork solutions with sleeved standard, C-ledgers, trigger brace, solid adjustable screw jack base , forkhead jacks, rail post etc.
Kwikstage Scaffolding Return transom allows a 90 degree turn in the scaffold and sit over the ledger allowing boards to run at right angles in adjacent bays. It can also be used to change direction. The use of Return Transoms eliminates the " gap " between runs at right angles.
Kwikstage Ladder Access Transom is used where a ladder access or trapdoor is required inside a bay. The Ladder Access Transom is located between the two ledgers, this is placed approx 64" from the previous transom. To be used with a Safety Trap-Door, a single section verticle ladder is held in place with 4 nos Metal Ladder Clamp. We recommend that 1
Kwikstage Mesh Panel / Brick Guard is placed between the ledger and the steel plank. Designed to be suspended from a guard rail ledger enclosing the space between the ledger and the working platform for safety.
Kwikstage Scaffolding Hop Up Brackets are used to give an extra work platform for scaffolding. Normally located on the inside face of the scaffold, these are 1, 2 and 3 board sizes.
Kwikstage Scaffolding Hop Up Brackets are used to give an extra work platform for scaffolding. Normally located on the inside face of the scaffold, these are 1, 2 and 3 board sizes. Hop Up Bracket with Post and Spigot allows to install scaffold vertical and ledger for safety railing.
Kwikstage Scaffolding Tie Bars have pins at each ends which fit in holes of 2 and 3 Hop Up Brackets to prevent the brackets spreading and the planks from becoming dislodged.
Kwikstage Internal Corner Board is used to fill in the gap ineternal corners when stage board brackets are used. It is a safe element to fill space between boards and standards to form a safe work platform and leveling. The internal corner boards sizes include one boards, 2 boards, 3 boards according to the width.
Kwikstage Scaffolding Steel Plank is a kind of plank which is designed and fabricated as per the Standard requirement of Australia/New Zealand AS 1577. It is made by 1.8mm or 1.5mm steel plate and hot dip galvanized. The planks are no hooks at both ends and to be installed onto the scaffolding transoms.
Kwikstage Scaffolding Toe Board / Kick Board is the component that prevents the building materials or tools falling off from working platform. The toe board has bolts at the ends to hold itself sitting between two verticals post of the platform.
Toe Board Clip is used to hold the toe baord to the scaffold working platform. The traditional Kwikstage Scafolding toe board clamp is fabricated by 5mm steel plate. And mostly the steel plank is always used the toe board.
