Stringer Stair is a popular stairway for system scaffolding in American market. It is set for 7' scaffold bay length, 6'7" high rising and for 3'6" wide access. The stair stringers and treads can be seperated. It can help to reduce job difficulty of when installing or dismantling the stair. Also it is much more convenient for material storage and t1
Aluminum Ladders are acted as scaffolding access, and popular for home uses, decoration jobs, building and construction, even for industry. Using high-quality, high-strength 6061-T6 aircraft grade aluminum alloy, the ladders are manufactured for extra safety and longer life.
H-Shoring Frame is a knid of traditional shoring scaffolding, it is a kind ladder frame for heavy duty support. It is made from O.D.60x3.5mm or O.D. 60x4.0mm high quality steel tube for frame leg, and O.D. 42x2.2mm tube for frame horizontals.
Side brackets allow for the extension of the scaffold platform beyond the legs, usually by a multiple of plank widths. When used with frame scaffolds, the side bracket is placed at the leg and is parallel to the frame or bearer. Angle Iron Side Bracket is the kind of bracket made by angle iron, with bell hanger.
Side brackets allow for the extension of the scaffold platform beyond the legs, usually by a multiple of plank widths. When used with frame scaffolds, the side bracket is placed at the leg and is parallel to the frame or bearer. Tubular Side Bracket is the kind of bracket that made by dia.1.65"x0.09"t (O.D 42x2.3mm) steel tube and with saddle hange1
End Bracket is the type of extension bracket, used to extend the platform at the end of a scaffold run. The end bracket is also placed at the leg but is perpendicular to the frame or bearer. Tubular End Bracket is made by dia.1.65"x0.09"t (O.D 42x2.3mm) steel tube and with bell hanger or saddle hanger.
Aluminum Plywood Ladder Hatch Deck is made by 6061-T6 or 6082-T6 aluminum extrusion and fire-proof plywood panel, plank width 24" or 28", plank length from 7' to 10'. Hatch Ladder: Aluminum 6061-T6, 7-step ladder The plank complies with OHSA & ANSI A10.8 requirements. Safety load is 75lb/ft2.
Mesh Ladders / Step Ladders / Steel Ladders / Straight Stairs are the economical stair acesses for H frames. The stair treads are made by 52x26x2.0mm steel oval tube, and the treads are made by mesh plates or punched hole plates or strip plates. They are used for 1219x1930mm H frames or cross lock scaffolding, for 1.83m or 2m scaffold bay.
Ring Lock Scaffolding Side bracket is used at the edge of a scaffolding to extend the reach or extension off of any side of the scaffolding where sunshade comes.
Kwikstage Ladder Access Transom is used where a ladder access or trapdoor is required inside a bay. The Ladder Access Transom is located between the two ledgers, this is placed approx 64" from the previous transom. To be used with a Safety Trap-Door, a single section verticle ladder is held in place with 4 nos Metal Ladder Clamp. We recommend that 1
Kwikstage Scaffolding Hop Up Brackets are used to give an extra work platform for scaffolding. Normally located on the inside face of the scaffold, these are 1, 2 and 3 board sizes.
Kwikstage Scaffolding Hop Up Brackets are used to give an extra work platform for scaffolding. Normally located on the inside face of the scaffold, these are 1, 2 and 3 board sizes. Hop Up Bracket with Post and Spigot allows to install scaffold vertical and ledger for safety railing.
Kwikstage Scaffolding Hop Down Bracket / Step Down Bracket gives balance and stability to the bottom step when getting on or off stair access at ground level. The first step onto stair access can be difficult due to site constraints, ground levels and base outs. The use of the step down bracket gives the comfort of adjustment to balance the variabl1
